DVI Video Matrix Switch: 32x32

• Matrix Switcher Video Input Type - Other
• Routing Type - Video
• Supported Resolution - WUXGA (1920x1200)
• Switcher Type - Video
• Warranty - Yes
• ROHS Compliant - Yes
• Rackmountable - Yes
• Spec Sheet available - Yes

• Video Input: Female DVI-I connectors. Signal type: single link digital DVI. Compatible with computers and HDTV video sources (satellite receivers, DVD players, etc) with DVI video. Multiplatform support: Windows 7/8/10, Windows Server 2008/2012/2016/2019, Solaris, Linux, FreeBSD, and MAC OS 10/11.
• Video Output: Female DVI-I connectors. Signal type: single link digital DVI. Supports HDTV resolutions up to 1080p, and up to 1920x1200 (WUXGA). Video bandwidth: 1.65 Gbps.
• Protocols: HTTP, HTTPS, TCP/IP, DHCP, UDP, ARP, TLS v1.2, IPV4.
• Power: 100 to 240 VAC at 50 or 60 Hz via IEC connector. (Country-specific power supply cable included.) 
• Cables: Use DVI-IS-xx-MM or DVI-HD-xx-MM cables to connect a DVI or HDMI source or display up to 15 ft away from the switch. Note: DVI cables longer than 15 feet may provide poor video performance with this switch. Interface cables between the video sources and the switch are required for proper operation. Cables not included.
• Regulatory Approvals: CE, RoHS.
• Warranty (Length/Type): Two years.
• Power Consumption: 45 W
• Dimensions: WxDxH (in): 19x16.17x7
• MTBF: 35,727 hrs.
• Operating Temperature (Maximum): 104 F
• Operating Temperature (Minimum): 32 F
• Certifications: CE, RoHS
• Input Impedance: 10,000 ohm
• Number of Inputs: 32
• Number of Outputs: 32
• Number of Video Inputs (Digital): 32
• Number of Video Outputs (Digital): 32
• Output Impedance: 0.10 ohm
• Rack Units (Height): 3
• Total Harmonic Distortion + Noise (THD+N): 0.01 %
• AC Voltage (Maximum): 240 Volts
• AC Voltage (Minimum): 100 Volts
• Active Power: 45 Watt
• Depth: 16 in
• Height: 7 in
• Width: 19 in
• Regulatory Compliance: CE, RoHS
• Compatible NTI Products: Combine NTI's extenders, switches, splitters and cables for complex applications HDMI Quad Screen Splitter/Multiviwer (SPLITMUX-HD-4RT). DVI-I Single Link Interface Cable (DVI-IS-xx-MM). DVI-D to HDMI Single Link Interface Cable (DVI-HD-xx-MM). Embedded audio will pass through the switch (with or without optional stereo audio) when an HDMI source is connected using DVI-HD-xx-MM. Stereo Audio Cable (SA-xx-MM). DVI Extender via Fiber Optic Cable (ST-2FODVI-LC). Embedded audio will pass through the switch and extender if an HDMI source is connected using an HDMI to DVI adapter. DVI Video Splitter (VOPEX-DVI-x). DVI/VGA Quad Screen Multiviewer (SPLITMUX-DVI-4). Screen Splitter / Video Wall Processor (SPLITMUX-SVDVI-4). HDMI HDBase-T Extender via One CAT5e/6 (ST-C6HD-HDBT). Mini HDMI Extender via Two CAT5e/6/6a (ST-C5HD-MINI-ULC). Only compatible for DVI input extensions with the DVI Matrix Switch. Mini DVI Extender via One CAT5/6/7 (ST-C5DVI-MINI). The extenders cannot be vertically adjacent to one another when connected to the switch.
• Control Method: Ethernet Control: Standard control method. Configuration can be done over the Internet via Web server or Telnet. Female RJ45 connector. 10/100 BaseT Ethernet interface. Web Server (view product demo) Security is ensured by password and user configurable timeout. Up to 25 users can access the web page at one time. The user can access the following pages: Switch page: allows the user to connect any input to any output, save and recall up to ten connections. Administration pages: administrator can access pages for system configuration, network configuration, naming video inputs/outputs, scanning sequence, DDC options, changing password, and updating firmware. Standby Mode page: allows the user to quickly place the switch in standby mode. Support page: provides links to the product manual and firmware downloads webpage. Reboot page: allows the user to quickly reboot the switch. Telnet Security is ensured by password. Up to 25 users can access the telnet connection at one time. Commands are similar to RS232 commands. The telnet server listens on ports 2000 and 2005. Port 2000 is for an operator telnet session. Port 2005 is intended for a software control type session using raw TCP communication.
• Control Method: Front Panel Interface: Standard control method Configuration and control can be done using the front panel buttons. Keypad allows selection of the input source to be routed to the desired outputs.
• Control Method: RS232: Standard control method Configuration and control can be done through the serial port. 4x4 switches: female RJ45 connector or female USB Type B connector. 8x8, 16x16, 32x32 switches: female RJ45 connector. Control the switch using the NTI Switch Control Program with Graphical User Interface (GUI control) via RS232.
• Control Method: Infrared Remote Control (Optional): Optional control method. IRT-UNV is sold separately. Transmitter can be up to 30 feet (9.1 meters) away. Control up to 15 switches with one remote. Power: Two AAA batteries (included).

DVI-HD-1M-MM
DVI-D Male to HDMI-A Male Cable - 1 m

DVI-HD-2M-MM
DVI-D Male to HDMI-A Male Cable - 2 m

DVI-HD-3M-MM
DVI-D Male to HDMI-A Male Cable - 3 m

DVI-HD-5M-MM
DVI-D Male to HDMI-A Male Cable - 5 m

DVI-IS-10-MM
DVI-I Cable, Male to Male - 10 ft

DVI-IS-15-MM
DVI-I Cable, Male to Male - 15 ft

DVI-IS-6-MM
DVI-I Cable, Male to Male - 6 ft

HDMIF-DVIDM
HDMI Female to DVI-D Male Adapter

IRT-UNV
Infrared Remote Control

SA-100-MM
Stereo Audio Cable, Male to Male - 100 ft

SA-10-MM
Stereo Audio Cable, Male to Male - 10 ft

SA-15-MM
Stereo Audio Cable, Male to Male - 15 ft

SA-25-MM
Stereo Audio Cable, Male to Male - 25 ft

SA-35-MM
Stereo Audio Cable, Male to Male - 35 ft

SA-3-MM
Stereo Audio Cable, Male to Male - 3 ft

SA-50-MM
Stereo Audio Cable, Male to Male - 50 ft

SA-6-MM
Stereo Audio Cable, Male to Male - 6 ft