Signalmanagment und -verarbeitung : Vorverstärker : RDL, Radio Design Labs - EZ-MPA2

Dual Microphone Preamplifier - Stereo Output with Compressors

Series:

Model: EZ-MPA2

Left and Right Balanced XLR Microphone Inputs
Switch-Selectable Phantom on Rear Panel
Unbalanced Output on MINI or RCA Jacks
Input and Output Connections on Rear Panel
Front-Panel Compressor Enable/Disable Switch

Weitere Produktinformationen

Vergleichen

Projektliste

Produktinformation

Spezifikationen

Zubehör

Dokumente

Accessoires

The EZ-MPA2 is a stereo microphone preamplifier with front-panel volume controls and audio level metering. A front-panel switch engages audio compressors to control overloads and clipping during high level audio bursts or peaks from the microphones. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The line output is available on RCA or MINI jacks. Left and right channel LED VU metering facilitates easy level adjustment. The EZ-MPA2 is ideal to add microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems.

Left and Right Balanced XLR Microphone Inputs
Switch-Selectable Phantom on Rear Panel
Unbalanced Output on MINI or RCA Jacks
Input and Output Connections on Rear Panel
Front-Panel Compressor Enable/Disable Switch
Audio Compressors Control Overloads
Front-Panel LEVEL Control for Each Channel
Dual-LED VU Meter for Each Channel
Optimized for Dynamic or Condenser Mics
Headroom Accomodates High Input Levels
Headroom Increases with Lower Gain Settings
Compressor Limits Clipping Over Wide Dynamic Range

Preamplifier Signal Type - Audio

Inputs (2):: 1.2 kΩ balanced on XLR jack, mic-level, -11 dBu max.
Level controls (2):: Off to 50 dB gain for each input
Outputs (2):: -10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
Frequency Response: 80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
THD+N:: < 0.1% (35 Hz to 20 kHz, -50 dBu input)
Compression:: 20 dB range, switch-selectable
Crosstalk:: Below noise floor (1 kHz)
CMRR:: > 55 dB (20 to 20 kHz)
Metering:: Dual-LED VU Meter for Left and Right, calibrated to -10 dBV output
Phantom:: Switch-selectable 24 V (IEC 1938: 1996-12)
24 Vdc power supply current:: 65 mA (idle), 90 mA (max.), 110 mA (max. with phantom)
Case dimensions:: 5.75” (14.6 cm)W x 3” (7.6 cm)D
Mounting size:: 1/3 rack width
DC-Spannung: 24 Volts
Tiefe: 76.20 mm
Width: 146.05 mm
Noise: -65 dBA
Shipping Weight: 0.45 kg

EZ-MCP1X - In-line Microphone Compressor

EZ-MPA1 - Microphone Preamplifier - Stereo Output with Compressors

FP-MP1 - Studio Quality Mic Preamp w/ Phantom - Terminals & XLR

FP-MPA2 - Dual Mic Phantom Adapter 12, 24, 48 V - XLR

HR-MP2 - Dual Microphone Preamplifier

HR-MP2A - Dual Microphone Preamplifier

ST-MPA24 - 24V Adjustable Dual Microphone Phantom Adapter

ST-MPA48 - 48V Fixed Dual Microphone Phantom Adapter

STM-1 - Microphone Preamplifier - 50 dB Gain

STM-2 - Adjustable Gain Mic Preamp - 35 to 65 dB Gain

STM-2X - Switched Mic Preamp - 35 to 65 dB Gain

STM-3 - High Gain Mic Preamp - 35 to 75 dB Gain

STM-LDA3 - Studio Quality Mic Preamp with phantom - 3 Line Outputs

EZ-MPA2_INSTALLATION_MANUAL.pdf 689 kb - Instructions

Projektliste

EZ-CC6
Component Chassis for 6 Increments of 1/6 Rack Width

EZ-DC2
Desktop Chassis for 1/3 Rack Width EZ Products

EZ-FP1
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6

EZ-RA6
Rack Adapter for 6 Increments of 1/6 Rack Width

EZ-SD1
Storage Drawer-1/6 Rack Width for EZ-RA6 or EZ-CC6

EZ-SD2
Storage Drawer - 1/3 Rack Width for EZ-RA6 or EZ-CC6

EZ-SMB2
Surface Mount Bezel for 1/3 Rack Width EZ Products

EZ-UCB2
Under Counter Bracket Pair for all EZ Product Widths