600 Ohms to 600 Ohms Repeat Coil Transformer

Model: JT-11SSP-6M

Ideal for use with low input impedance circuits
Wide bandwidth of -3dB at 0.4Hz and 220kHz
Recommended for levels up to +19dBu at 20Hz
Insertion loss only 1.9dB in 600ohm to 600ohm application
High common-mode rejection of 110dB at 60Hz

More Product Information Below

Compare

Project List

Product Info

Tech Specs

Related Products

Documents

Line input transformers provide the maximum possible Common Mode Rejection of unwanted signals. All models have a single Faraday shield and a 30dB magnetic shield can. Models are available in 1:1, 1:1.4, 1:2, 2:1 and 4:1 ratios. Several models are also available as octal plug-in versions. This transformer has split primary and secondary windings which can be connected for 1:2 (150:600ohm), 1:1 (600:600ohm) or 2:1 (600:150ohm) operation. Distortion, although specified for 600ohm sources, will be further reduced by lower impedances. A 30dB magnetic shield package is standard.

Ideal for use with low input impedance circuits
Wide bandwidth of -3dB at 0.4Hz and 220kHz
Recommended for levels up to +19dBu at 20Hz
Insertion loss only 1.9dB in 600ohm to 600ohm application
High common-mode rejection of 110dB at 60Hz

Audio Transformer Type - Internal Transformer
Audio Transformer Type - Line Transformer
Spec Sheet available - Yes

Operating Temperature (Maximum): 158 F
Operating Temperature (Minimum): 32 F
Maximum Bandwidth: 220 kHz (-3dB)
Impedance Ratio: 600:600, 600:150 and 150:600
Input Impedance: 745 kohm (1kHz, +4dBu, test circuit 1)
Voltage Gain: -1.9 dB (1kHz, +4dBu, test circuit 1)
Magnitude response, ref 1 kHz: -0.05 (20Hz, +4dBu, test circuit 1, Rs=600ohm) and -0.01 (20kHz, +4dBu, test circuit 1, Rs=600ohm) dB
Deviation from linear phase (DLP): +0.6/-0 degree (20Hz to 20kHz, +4dBu, test circuit 1, Rs=600ohm)
Distortion (THD): <0.001 (1kHz, +4dBu, test circuit 1, Rs=600ohm) and 0.04 (20Hz, +4dBu, test circuit 1, Rs=600ohm) %
Maximum 20Hz input level: +19 dBu (1% THD, test circuit 1, Rs=600ohm)
Common-mode rejection ratio (CMRR) 50ohm balanced source: 110 (60Hz, test circuit 2) and 75 (3kHz, test circuit 2) dB
Common-mode rejection ratio (CMRR) 600ohm unbalanced source: 79 (60Hz, test circuit 3) and 45 (3kHz, test circuit 3) dB
Output Impedance: 745 ohm (1kHz, test circuit 1, Rs=600ohm)
Total primary DC resistance: 32 ohm (RED to ORG)
Total secondary DC resistances: 113 ohm (GRY to GRN)
Capacitance at 1kHz: 950pF (total primary to shield and case) and 1.12nF (total secondary to shield and case)
Turns Ratio: 1.000:1 any winding to any other winding
Breakdown Voltage: 250 Vrms (primary or secondary to shield and case, 60Hz, 1 minute test duration)

JT-11SSP-7MPC - Standard Wide Bandwidth Line Input Transformer

Transformer 188 kb - Data Sheet

Project List

Request Quote

Find a Dealer

Suggested Products

Audio Isolation Transformer with Suppression

by RDL, Radio Design Labs

Headphone Isolation Transformer

by RDL, Radio Design Labs

Unbalanced Input Transformer - Unbalanced stereo inputs to summed balanced mono output

by RDL, Radio Design Labs