Lighting Control Systems : Lighting Control Panels & Consoles : AMX - CCD-6CL

600W Clear Connect CFL+LED Incandescent/MLV Dimmer

Model: CCD-6CL

Part #: FG2606-14-WH

Clear Connect Enabled – Lutron's patented RF Technology uses a quiet band, essentially free of interference ensuring reliable communication between system devices
Perfect Way to Add Light Control – Easily integrates with existing electrical infrastructures - simply replace the light switch
Simple Web Configuration – Browse to the NetLinx® Clear Connect Gateway URL to quickly setup the Clear Connect Dimmers

More Product Information Below

Compare

Project List

Product Info

Tech Specs

This Product is Available Only in the U.S. and Canada
OVERVIEW

The Clear Connect™ CCD-6CL Dimmer is capable of controlling up to 150 Watt Dimmable CFL / LEDs or 600 Watt Incandescent / Halogen or Mixed bulb types. This versatile dimmer offers more reliable performance over incandescent dimmers when controlling CFLs and LEDs. It also provides the capability to adjust the low-end of the dimming range based on the capability of each supported bulb.

Clear Connect Enabled – Lutron's patented RF Technology uses a quiet band, essentially free of interference ensuring reliable communication between system devices
Perfect Way to Add Light Control – Easily integrates with existing electrical infrastructures - simply replace the light switch
Simple Web Configuration – Browse to the NetLinx® Clear Connect Gateway URL to quickly setup the Clear Connect Dimmers

Warranty - Yes

Certifications: UL, FCC
Operating Temperature (Maximum): 40 C
Operating Temperature (Minimum): 0 C
Warranty (Length/Type): 3 Years Limited
Power:
- Power: 120 V 50 / 60 Hz
  - Maximum Load: - 150 W Dimmable CFL/LED or - 600 W Incandescent/Halogen or - Mixed bulb type per Multigang and Mixed Bulb Type Ratings table
  - Minimum Load: - See Dimmable CFL & LED bulbs compatible list for Maestro C•L dimmers: Maestro® C•L: MACL-153M
- Typical Power Consumption
  - Dimmer / Switch: 0.2 W
  - Test conditions: load is off and nightlight mode is enabled
  - Remote Dimmer / Switch: 0 W
  - Test conditions: load is off
- Surge Protection: To withstand surge voltages without damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits
- Power Failure: Power failure memory: should power be interrupted, the Clear Connect Gateway will return to its previous state when power is restored
Environmental:
- Operating Humidity: 0% to 90%, non-condensing
- Indoor use only
ESD Protection:
- To withstand electrostatic discharge without damage or memory loss, in accordance with IEC 61000-4-2
COMMUNICATIONS:
- Dimmers and switches communicate with the system through Radio Frequency (RF) and must be located within 30 ft (9 m) of a repeater
- Remote dimmers / switches are not required to be within a specific range of a repeater. System devices operate on frequencies between 431.0 MHz and 437.0 MHz
Installation:
- Mounting Requires a U.S. wallbox. 3 . in (89 mm) deep recommended, 2 . in (57 mm) deep minimum
- Wiring Uses conventional 3-way and 4-way wiring
Certifications:
- CSA , NOM, IC, COFETEL
Operating Humidity: 0 to 90 % Non-condensing

Find a Dealer

Find a Distributor

Suggested Products

RPC 329 N Remote Power Control Panel, Narrow/Column Width,3Ø, 4 wire, 208Y/120Vac, 100A Main, Holds 29 breakers, Controls up to 155 breakers.

by LynTec, Inc.

LCP 339N Lighting Control Panelboard, Narrow/Column Width, 3Ø, 4 wire, 208Y/120Vac, 225A Main, Holds 39 breakers, Controls up to 165 breakers. Includes LCP controller in separate enclosure.

by LynTec, Inc.

LCP 327N Lighting Control Panelboard, Narrow/Column Width, 3Ø, 4 wire, 208Y/120Vac, 100A Main, Holds 27 breakers, Controls up to 152 breakers. Includes LCP controller in separate enclosure.

by LynTec, Inc.